Mould Release Oil 5Lt for Easy Release from All Types of Concrete Moulds and Forms 5 Litre

Product Information

This is a water-based mould releasing agent which gives clean and stain free high-quality concrete. It is available in a sprayable form and ready to use as a direct application on required places. It should be applied in light film either by brush or mould oil sprayer. If it is over applied, excess oil should be drained before it dries. Pools of DSO cannot be allowed to dry as it causes surface retardation of concrete. Our Mould Oil helps ensure that formwork remains free of concrete deposits is therefore an essential task and an efficient and powerful cleaning agent is a vital product to get the job done. THORCAST Mould Oil is a formulated blend of mineral oils with additives and a degree of surfactant designed to work as a concrete release oil for demoulding concrete from all types of formwork moulds. It can be used on a wide range of metal, proprietary timber, ply and other formwork materials and coatings, however if using on plastic or rubber moulds consideration should be given to using our Norsekem Teknistrip. Formulated to give optimum release and quality of finish to concrete over a wide range of mix designs. Product is low hazard and not labelled as flammable. There are several types of natural cleaning solutions that can work to remove mould from wood. Some are more suitable for painted wooden surfaces, such mould on skirting boards or window frames, while others are best for bare wood.

sq. ft/USGal (17.7-36.8 sq.m/L), depending on the type and porosity of the form surface. Precautions However, before any mould problems can be fully resolved, it is vital to understand what causes dampso you can work out where the problem is originating. Damp and condensation are both prime causes of mould on all kinds of areas of the house, from walls and ceilings to wooden furniture and even fabrics such as curtains.Work the solution into the wood, leave it to get to work for a hour or so then wipe away using a damp cloth. THORCAST mould release oil in manufacturer’s sealed drums requires no special storage facilities. Product is not flammable These “Mould Oils” are applied to steel and timber formwork and falsework to reduce the cohesion between the curing concrete and the shuttering. In the case of wooden formwork, shuttering oil prevents water absorption from concrete by the wooden formwork. Clean all form surfaces thoroughly prior to application. Remove all rust, scale and/or previously used form release agents from the forms, in accordance with good concrete practices. It is imperative when using new timber forms of all types (plain wooden, plywood, rough cut etc.) that Speed//STRIKE be applied and reapplied until complete saturation has been accomplished prior to first use. Application

Once the concrete is set, the shuttering is removed and the process repeated.The use of mould oil also extends the life of your road forms and concrete shuttering, protecting equipment from concrete build up, and ensuring strong and accurate edges and easy formwork release. Many new forms are not factory treated with oils, so for new or ‘unsealed’ timber formwork, pre-treatment is essential with two to three coats prior to use. This will extend the useful life of the form and help to standardise surface absorbency. For unsealed ply consideration could also be given to primary sealing with NORSEKEM SHUTTAWAX or NORSEKEM FORMSEAL PU1K sealer Mould oils play an essential role in enabling efficient production processes, enhancing product quality, and extending the life of moulds in diverse industries such as manufacturing, construction, automotive, and plastics. What mould oils can you supply? Speed//STRIKE Formwork Release Agent meets the maximum capacity of VOC content for form release compounds of 450 g/l. Directions Surface Preparation When working with mould oils, it is vital to prioritise safety by adhering to guidelines and considering the specific requirements of the manufacturing process. Some oils may necessitate proper ventilation, the use of protective gear, or compliance with environmental regulations to ensure a safe working environment.Product is supplied ready for use do not dilute. All formwork surfaces should be clean prior to application. Apply a thin uniform coating to the formwork surface avoiding over application. Spraying is the preferred method of application using a sprayer such as a Mesto Ferrox Plus 3585P or Mesto Profi Plus 3270P with an 8001 Nozzle fitted , however brushes or rollers may be used. Ensure any excess is mopped up as over application can cause dusty concrete, pay particular attention to the bottom of vertical shutter for run off. Before the application of shuttering oil on the formwork, it is important to make sure that the surface of the formwork is clean of previous impurities. The shuttering oil is applied by spraying guns, rollers or by brushes. It is important to remove any excess oil on the surface of the formwork.

Both baking soda and vinegar are a better choice for killing off mould than bleach. You can use them separately or combine them to create your own mould killer." The first is to use a solution made up from vinegar and water — in equal parts. Vinegar will not only get rid of the mould but it should also help eliminate or at the very least fade out, the stains. Use a spray bottle to apply the solution, allow it to sit for a couple of hours, then wipe the area down with a damp cloth or rag.Mould on bare wood can be harder to remove than that on painted wood —a light sanding after removal can really help. (Image credit: Getty) Which products remove mould from wood? Applying mould oils is a flexible process that can be accomplished through various methods such as spraying, brushing, or wiping onto the mould surface. The choice of application method depends on factors like mould type, accessibility, and the consistency of the oil being used. If the wood in question has not been painted or varnished, you might need to take a different approach. This is because you need your cleaning solution to penetrate the wood to eliminate any spores that have permeated the timber. Also Read: Types of Formwork (Shuttering) for Concrete Construction and its Properties Types of Shuttering oil: 1. De-Shuttering Oil (DSO)

DSO provides a damp proof interface that protects the formwork and ensures even texture and colour of concrete. CMT Group ensures that you, our valued customer, enjoys your shopping experience as we strive to make your experience ‘hassle free’. This stuff worked a treat," says Amy. "I had an old bottle lying around and sprayed it on. I waited just over five minutes and wiped and off it came. I was actually pleasantly surprised how easily it came off. Note, it did leave a bit of a chlorine smell like a swimming pool, which I didn't mind as it made the bathroom smell clean but it might bother some." What causes mould to grow on wood?

At Trent Oil, we aim to supply the best quality concrete mould release oils to our construction and manufacturing customers. Our specially designed oils for mould release are available in an assortment of sizes and quantities.